Link Search Menu Expand Document

Gate Signal Analysis with Oscilloscope

After successfully completing the initial smoke test, the next crucial step in validating the KISRAK-M1 motor driver is to analyze the gate signals of the power MOSFETs using an oscilloscope. This analysis provides critical insights into the switching performance, dead-time implementation, and overall health of the gate drive stage.

Objectives of Gate Signal Analysis:

  • Verify Gate Drive Waveforms: Ensure the gate signals are clean, have the correct voltage levels, and exhibit proper rise and fall times.
  • Confirm Dead-Time: Visually confirm the presence and duration of the dead-time between complementary MOSFETs in a half-bridge.
  • Measure Rise/Fall Times: Quantify the switching speed of the MOSFETs, which directly impacts switching losses and efficiency.
  • Identify Issues: Detect problems such as ringing, oscillations, insufficient gate voltage, or slow switching that could lead to inefficiency or damage.

Tools Required:

  • Oscilloscope: A digital storage oscilloscope (DSO) with at least two channels and sufficient bandwidth (e.g., 100MHz or more).
  • High-Impedance Probes: Standard 10x passive probes are usually sufficient.
  • Current-Limited DC Power Supply: For safety during testing.
  • Function Generator / Microcontroller: To provide PWM signals to the KISRAK-M1 inputs.
  • Small DC Motor (optional): For testing under load, though initial tests can be done without a motor.

Protocol for Gate Signal Analysis:


Step 1: Setup and Initial Power-Up

  1. Connect Power: Connect the current-limited power supply to KISRAK-M1, set to a low operating voltage (e.g., 5V) and a safe current limit (e.g., 500mA).
  2. Connect Function Generator/MCU: Connect your function generator or microcontroller to the input pins of KISRAK-M1, configured to generate a low-frequency PWM signal (e.g., 1kHz - 5kHz) with a moderate duty cycle (e.g., 50%). This makes it easier to observe individual switching events.
  3. Connect Oscilloscope Probes:
    • Connect the ground clip of both probes to a solid ground point on the KISRAK-M1 PCB, as close as possible to the MOSFETs being measured.
    • Probe 1: Connect to the gate of a high-side P-Channel MOSFET (e.g., Q1).
    • Probe 2: Connect to the gate of its complementary low-side N-Channel MOSFET (e.g., Q3) in the same half-bridge leg.

Step 2: Observe and Analyze Gate Waveforms

  1. Triggering: Set the oscilloscope to trigger on one of the gate signals (e.g., rising edge of the low-side MOSFET gate).
  2. Timebase and Vertical Scale: Adjust the timebase (e.g., 1µs/div to 10µs/div) and vertical scale (e.g., 2V/div to 5V/div) to clearly see the full gate voltage swing and the switching transitions.
  3. Expected Waveforms:
    • Low-Side N-Channel MOSFET Gate (e.g., Q3): Should swing from 0V to the gate drive voltage (e.g., 5V).
    • High-Side P-Channel MOSFET Gate (e.g., Q1): Should swing from $V_{bat}$ (when OFF) down to $V_{bat} - V_{drive}$ (when ON). For example, if $V_{bat}=5V$ and drive is 5V, it would swing from 5V to 0V. If the drive is 3.3V, it would swing from 5V to 1.7V.
  4. Key Measurements and Observations:

    • Gate Voltage Levels:
      • Ensure the gate voltage swings fully between its ON and OFF states. For N-channel, typically 0V to $V_{drive}$. For P-channel, typically $V_{bat}$ to $V_{bat} - V_{drive}$.
      • Insufficient gate voltage swing can lead to the MOSFET not fully turning ON, increasing $R_{DS(on)}$ and conduction losses.
    • Rise Time ($t_r$) and Fall Time ($t_f$):
      • Measure the time it takes for the gate voltage to rise from 10% to 90% of its final value (rise time) and fall from 90% to 10% (fall time).
      • These times should be fast (typically in the tens to hundreds of nanoseconds) due to the Totem-Pole driver. Slower times indicate issues with the gate driver or excessive gate capacitance.
    • Dead-Time:
      • This is the most critical observation. Zoom in on the transition period where one MOSFET turns off and the other turns on.
      • There should be a clear, measurable delay where both gate signals are in their OFF state (low for N-channel, high for P-channel).
      • Measure this dead-time. It should correspond roughly to the calculated time constant of the RC-D network (e.g., ~100ns).
      • Absence of Dead-Time: If the gate signals overlap (one turns on before the other fully turns off), it indicates a shoot-through condition, which is highly destructive. This requires immediate investigation of the RC-D circuit and gate driver.
    • Ringing and Oscillations:
      • Look for any excessive ringing or oscillations on the gate waveforms, especially during transitions. This can be caused by parasitic inductances and capacitances and can lead to false triggering or increased EMI. Minor ringing is often acceptable, but large, sustained oscillations are problematic.

Step 3: Repeat for All Half-Bridges

Repeat the analysis for all half-bridges in the KISRAK-M1 driver to ensure consistent performance across all motor channels.

By meticulously performing gate signal analysis, I can confirm the proper operation of the KISRAK-M1’s gate drive stage and dead-time implementation, which are fundamental to its efficiency and reliability. This step is indispensable for validating the hardware design.